Ingress protection testing is usually described as a test of the seals. In practice a large share of failures happen at the two features that are not seals at all: the drain hole that lets water out and the vent membrane that lets air in. Both are deliberate openings, both are necessary, and both are frequently specified without a thought for what they do during the test.
The drain hole is a two-way door
A drain hole is sized to let water leave under gravity. During a spray or a jet, the same hole admits water at a rate set by the impact pressure, not by gravity, and a hole that drains 200 mL/min at rest can admit 400 mL/min under a jet at 30 kPa. The net flow reverses for the duration of the test.
The fix is not to remove the hole but to give it a direction. A lip, a downward-facing shroud, or a flap that opens outward and closes under reverse flow all preserve drainage while resisting ingress. The design rule that works: the drain path should have at least one change of direction, and the opening should face down within 30 degrees of vertical.
| Feature | Dry performance | Behaviour under spray or jet | Design answer |
| Open drain hole, 4 mm, facing down | Drains 200 mL/min | Admits water at impact pressure | Add lip or flap |
| Labyrinth drain, two 90° turns | Drains 120 mL/min | Admits very little | Preferred where space allows |
| Vent membrane, ePTFE | Breathes air freely | Passes vapour, blocks liquid | Keep membrane area ≥ 100 mm² |
| Vent membrane wet with surfactant | Breathes air | Liquid can wick through | Avoid detergents on the membrane |
| Sealed vent, no membrane | No breathing | Pressure differential on gasket | Add membrane or accept pumping |
The vent membrane and the pressure it relieves
A sealed enclosure is a pressure vessel with a weak wall. Heat from an internal source raises the internal pressure, and the gasket sees a load it was not designed for. The standard remedy is an ePTFE membrane: it passes air at a few hundred mL/min while holding a water-entry pressure well above anything a spray can produce.
Two conditions have to hold for that to remain true. The membrane must be large enough that the airflow does not become the limiting factor, and it must stay uncontaminated. A membrane wiped with a detergent, or exposed to oil mist, wets out; the pores fill with liquid and the membrane stops breathing. It still looks intact, still passes the cosmetic check, and the enclosure now pumps water past the gasket on every thermal cycle.
Testing the two features specifically
A general IP test tells you the assembly passed or failed. It does not tell you which path admitted the water, and without that, the corrective action is a guess. Two extra checks are worth the time:
- Weigh the unit before and after the test. A change of more than 1 g on a 2 kg unit is water you have to account for, even if the inside looks dry.
- Dry the exterior, then invert the unit and collect what drains for 10 minutes. Water that comes out on inversion entered during the test and pooled in a cavity that does not drain.
- Block the drain hole with tape and repeat a short spray. If the ingress disappears, the hole was the path; if it does not, look at the membrane and the gasket.
Where the two features interact
A drain hole and a vent membrane in the same cavity form a breathing system. During a thermal cycle the membrane lets air in and out, and the drain hole lets water in but not out if the cavity is under positive pressure at the wrong moment. The result is a slow accumulation that only shows up after 20 or 30 cycles, long after the type test.
The arrangement that avoids it: put the membrane high and the drain low, on opposite walls, so that the air path and the water path do not share a route. A 50 mm separation is usually enough, and it costs nothing at the design stage and a redesign later.
Standards referenced: IEC 60529 (degrees of protection provided by enclosures), IEC 60068-2-30 for the cyclic damp heat that drives the breathing mechanism.
