Dust ingress testing is the only part of the IP code where the specimen is actively involved in creating the condition being tested. Water tests apply water to the outside. The dust test lowers the pressure inside the enclosure so that the surrounding dust-laden air is drawn in through whatever gaps exist. If the vacuum is wrong, the test is not the test.
The conditions that define the two levels
| Condition | IP5X | IP6X |
| Chamber dust | Talcum powder, fine and free-flowing | Same |
| Duration | 8 hours | 8 hours |
| Pressure differential | Up to 2 kPa below ambient | Up to 2 kPa below ambient |
| Air extraction | About 40 volumes per hour, not more than 60 | Same |
| Acceptance | Dust may enter but not in sufficient quantity to interfere with operation or safety | No dust deposition inside the enclosure |
The two levels use the same apparatus and the same conditions, as set out in IEC 60529. The difference is entirely in the acceptance criterion, which is why a product designed for IP6X is tested identically and judged more strictly. A laboratory that "tests harder" for IP6X by extending the duration is not following the standard and will produce results that cannot be compared.
Why the vacuum is the test
An enclosure at ambient pressure has no driving force for dust entry beyond diffusion, which is negligible over 8 hours. The vacuum creates a pressure difference that pulls air — and the dust it carries — through gaskets, cable entries and screw threads. Three consequences follow:
- No vacuum, no test. A specimen tested without a pressure connection has been exposed to dust, not tested for ingress.
- Too much vacuum is also wrong. Exceeding 2 kPa can deform seals or pull gaskets into the enclosure, creating a failure that would not occur in service.
- The vacuum must be continuous. A single evacuation at the start leaks down through the very gaps being tested and stops driving dust within minutes.
What the specimen needs
Every enclosure under test needs a pressure connection that reaches the internal volume. Three common situations:
- Enclosure with a cable gland. Connect through the gland with a suitable adaptor, and seal the adaptor so the only path into the volume is through the product's own gaps.
- Sealed enclosure with no entry. Drill and tap a temporary port, test, and plug it. Record the port location, because the plug is now part of the enclosure.
- Enclosure with a membrane vent. The vent passes air but may retain dust. Test through the vent as the product does, and note that the vent's dust behaviour is part of what is being measured.
Talcum, not sand
The test medium is talcum powder, which is fine enough to behave as an aerosol and to follow airflow through gaps measured in tens of micrometres. Sand, cement or Arizona test dust are different tests with different purposes and are not interchangeable. Two practical points:
- Powder that has absorbed moisture cakes and will not aerosolise. Store it dry and replace it when it starts to clump.
- Powder that has been used many times becomes coarser as the fine fraction is lost to the filters. Replace it on a schedule, not when the chamber looks dirty.
Reading the result
For IP5X, the judgement is functional: dust inside is acceptable if it does not interfere with operation or reduce creepage and clearance below the product standard's values. That requires opening the specimen and looking at specific places, not a general inspection:
- Across creepage paths and clearance gaps, particularly around terminals.
- On optical surfaces, where a light film changes performance more than a visible deposit on a housing wall.
- In bearings and sliding surfaces, where dust causes wear rather than electrical failure.
- On any surface that will later condense moisture, since dust plus condensation is a conductive path.
For IP6X the criterion is simpler to state and harder to meet: no deposition inside. A single visible trace at a gasket edge is a fail, and the trace is usually the evidence that the vacuum pulled dust through a seal that was marginal in the first place.
Correlating with the water test
Dust and water ingress are related but not equivalent, and a product can pass one and fail the other. A labyrinth that stops a 1 mm water jet can pass dust freely under vacuum; a gasket that seals against dust can fail under a jet because it is not designed for pressure. When a product is claimed at IP66, both tests have to be run, in the order the product standard specifies.
The ingress protection range includes dust chambers with vacuum control and talcum dosing; the catalogue indexes the jet and immersion apparatus used for the second digit.
